Heating and cooling calls in Canyon Lake reach a person who can scope the job and get it on the calendar. For a planned installation or a full system replacement, the schedule is worked out on the call and confirmed before anything is booked. For a system that has stopped working, we prioritize getting somebody out. We are available every day from 6:00 AM to 9:30 PM, and the price for the visit is set on the phone before it is scheduled.
Canyon Lake is a city with a lot of residential property, and much of that housing stock carries equipment that has run through many warm seasons without a proper look. Homes with additions, detached structures, and rooms that were never quite comfortable are common here. We work through all of it: AC repair, heating and furnace service, heat pump installation and repair, full system replacement, ductwork, thermostats, and indoor air quality.
Call (830) 632-8965 to get started.
The price depends on what the job actually turns out to be. A service call that finds a failing capacitor is a different conversation from one that finds a refrigerant leak or a cracked heat exchanger. What has to be accessed, how old the equipment is, and whether a repair makes sense against the cost of replacement all move the number. We go through that on the call and confirm the rate before the visit is scheduled, so you know what you are agreeing to before anyone comes out.
What would change a quote: the scope of the diagnostic, whether the system needs refrigerant added or a leak found and sealed, whether the blower motor or air handler needs work, and whether the job turns into a replacement conversation once the equipment has been looked at properly. None of that is guesswork on the phone. The diagnosis explained on every call means the visit does not end with a surprise. Ask what the visit covers and you get a straight answer.
We do not offer a free estimate or a free inspection. The rate is discussed on the call and confirmed before anything is scheduled.
A thermostat that is reading the room temperature incorrectly, failing to hold a set point, or losing its settings after a power interruption is not a minor inconvenience. It is the control that tells the entire system when to run and when to stop, and a bad one makes a working system behave like a broken one. Short cycling, rooms that never reach temperature, and equipment that runs longer than it should are all symptoms that start at the thermostat as often as they start at the equipment itself.
Replacing a failing thermostat is one of the more straightforward jobs on a heating and cooling system, and the price is confirmed before the visit.
A modern smart thermostat does more than hold a temperature. It learns usage patterns, adjusts setpoints based on occupancy, and gives a homeowner remote access from a phone. For a property with rooms that are used differently at different times, a zoned control setup handles each area independently rather than running the whole system for one occupied room.
We handle thermostat and smart-control installation as a standalone job, not only as part of a larger replacement. If the equipment is sound but the controls are outdated, that is a reasonable place to start.
A system that goes out in the middle of a hot stretch or on a cold night does not wait for a weekday opening. We take emergency no-heat and no-cool calls every day from 6:00 AM to 9:30 PM. When you call, we scope the job on the phone: what the system is doing, what it was doing before it stopped, and what the visit will involve. The price is confirmed before anything is put on the schedule.
We do not quote arrival windows, but emergency work is handled with priority. Short-notice appointments are something we take on regularly.
For a rental property with a tenant in place, or a small commercial space that cannot close during a repair, we work through what the visit requires and what access is needed before the technician arrives. The scope and the timing are settled on the call. Nothing about the job changes because a property is occupied, but knowing the situation ahead of time keeps the visit from creating a problem for whoever is there. Anyone sizing up a job in Canyon Lake may want to read the HVAC service list first.
When the outdoor unit is running but the air coming through the vents is not cold, the fault is often at the compressor or the condenser coil. A compressor that is drawing high amperage, a condenser coil that has lost its ability to shed heat, or a refrigerant charge that has dropped below the correct level are all common causes. Refrigerant leak diagnosis is part of this work. Adding refrigerant without finding the source of the loss is a short-term fix, and we do not treat it as a solution.
A single thermostat controlling a house with rooms that face different directions, have different ceiling heights, or are used at different times of day is always going to leave somebody uncomfortable. Zoning splits the system into independently controlled areas, each with its own setpoint. For homes where one side of the house runs hot and the other runs cool, or where a bonus room never matches the rest of the house, zoning is often the fix rather than a bigger system. Mini-split and ductless systems handle this for spaces where running new ductwork is not practical.
Leaky ductwork loses conditioned air before it reaches the room it was meant for. In a home where some rooms have always been harder to heat or cool than others, the duct system is worth checking before the equipment is blamed. We handle duct sealing and repair as a standalone job. Airflow balanced rather than left to chance means the system performs the way it was designed to, not just the way it has always been set up.
The air handler and blower motor are the parts of the system most people never think about until they stop working. A blower motor that is running slow, drawing too much current, or making noise is reducing airflow across the whole system. That shows up as longer run times, higher utility use, and rooms that never quite get there. We diagnose and service air handlers as part of both repair calls and maintenance visits.
A tune-up before the cooling season means the AC goes into summer with clean coils, confirmed refrigerant charge, and a blower that has been checked. A heating tune-up before the first cold front means the furnace or heat pump has been looked at while there is still time to address what is found. In a region with humid summers and real heating demand in winter, both are worth scheduling. The visit covers what the system actually needs, not a checklist run through in twenty minutes.
When the technician arrives, the first thing that happens is a conversation about what the system has been doing. What the symptom is, when it started, and whether anything changed before it appeared all narrow down where to look. From there, the diagnostic works through the components most likely to produce that symptom rather than checking everything in sequence regardless of what the call described.
What was found is explained before any repair is quoted. Nothing gets replaced before you know why. If the diagnostic turns up something beyond what was discussed on the phone, that gets explained before any additional work is done. The price for the additional scope is confirmed before anything moves forward.
No pressure and no gimmicks, just straight HVAC answers. The visit ends with a clear picture of what the system needs, what it will cost, and what happens next.
We serve Canyon Lake and the surrounding communities across Comal County. That includes Spring Branch, Bulverde, and Wimberley, as well as Woodcreek and the broader area around the lake. Calls about this area are answered by someone who knows the trade and can scope the job on the phone.
If your address is in or near Canyon Lake and you are not sure whether it falls within the service area, the call will confirm it quickly. We cover residential and commercial properties across the region, and the process is the same wherever the job is: scope it on the phone, confirm the price, then schedule.
Yes. If the system is still running and the replacement is planned rather than emergency, we can schedule it ahead. Call us to confirm availability and get the price on the phone, and we will put it on the schedule from there.
A system that runs without satisfying the thermostat is either undersized for the load, losing refrigerant, dealing with a dirty coil that cannot transfer heat efficiently, or fighting a significant duct leak. The diagnostic works through those possibilities in order rather than assuming the most expensive cause first.
If the system is running but not cooling or heating, it is generally better to turn it off at the thermostat rather than let it run. A system that is running without doing useful work can overheat components or run a compressor without adequate refrigerant, which causes additional damage. If the system has stopped on its own, leave it off until the visit.
The system can be checked if access to the equipment is available, but having someone present is helpful for two reasons. The technician can ask questions about what the system was doing before the call, and any findings and next steps are easier to communicate directly. If the property will be unoccupied, let us know when you book so we can plan accordingly.
The answer to that question changes once somebody has actually looked at the equipment. A system that has been running poorly for a season might need one repair. It might be a candidate for replacement. It might have a duct problem that has nothing to do with the equipment itself. The only way to know is a proper diagnostic, and that starts with a call.
Call New Braunfels HVAC Company at (830) 632-8965.
We are available every day from 6:00 AM to 9:30 PM. The price is confirmed before the visit is scheduled, and the diagnosis explained on every call means you go into the decision with the full picture.
Also close at hand: Bulverde, Wimberley, Garden Ridge, Timberwood Park. Check our complete coverage area.
From a quick AC repair to a full system replacement, we handle the heating and cooling work that keeps Canyon Lake homes and commercial buildings running through long Texas summers and the cold fronts that follow. The services below cover the full range of what we do, along with what each visit includes, who it fits best, and a practical note on timing or value. Call us with any questions and we will walk through the options before anything is scheduled.
| HVAC Service | What It Covers | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Whole-Home Dehumidification & Humidity Control | Dehumidifier sizing and selectionAir handler integrationHumidity target settingSystem test across the full home | Comal County homes where indoor air feels heavy or musty even when the AC is running | High indoor humidity in this region can persist through spring and fall even when temperatures are manageable. A whole-home unit operates independently of the cooling cycle and holds humidity to a set target. |
| Full System Installation & ReplacementMost Popular | Load calculation and proper sizingMatched condenser, air handler, and coilRefrigerant line and electrical connectionsSystem testing and airflow verification | Homeowners whose system is aging, requiring repeated repairs, or no longer keeping up with the cooling load | Replacing components from the same equipment generation keeps efficiency ratings accurate and avoids compatibility problems that come from mixing old and new hardware. |
| Seasonal Maintenance & Tune-Ups | Cooling or heating system inspectionCoil cleaning and refrigerant checkBlower and electrical component testingFilter check and airflow assessment | Homeowners who want to catch problems before a season starts rather than during it | Spring is the right window for a cooling tune-up before the long Texas summer. Early fall works for heating. Both windows are before demand for service peaks. |
Call us at (830) 632-8965 and we will go through the details, confirm the price, and get the right service scheduled for your home or building.
(830) 632-8965